The product will transform AC 100-240V into DC 14 V, its maximal output power reaches 250W, it may power most 10-18 V chargers.

Connect any Charger which is supposed to be powered by DC 10-18V, the switching power supply will provide up to 17 Amps. it is also equipped with both US / Japan and Europe AC plugs and works using 100 - 240V AC so it may be used internationally.

Feature：

1. Switching technology
2. Light & Convenient Plug In
3. Over current protection
4. Dual channel output for more application
5. Intelligent cooling fan starting automatically upon internal temperature

Description: G.T. POWER A6-D BALANCE CHARGER/DISCHARGER

Operating voltage range: DC 11.0-18.0Volt/ AC 100-240V

Wall plug type: 3-pin squared (in angle)

Circuit power: Max 50W for charging

Max 5W for discharging

Charge current range: 0.1-5.0A

Discharge current range: 0.1-1.0A

Current drain for balancing Li-Po: 300mAh/cell

NiCd/NiMH battery cell count: 1-15 cells

Li-ion/Polymer battery cell count: 1-6 series

Pb battery voltage: 2V,20V

Net weight: 600g

Dimensions: 165×130×45mm

Includes:
1 x charger
1 x Alligator Clips to DC Cable
1 x alligator clips to Dean style connector cable
1 x glow heater plug to Dean style connector cable
1 x banana connector to Dean style connector cable
1 x JST connector to Dean style connector cable
1 x Futaba connector to Dean style connector cable
1 x manual

The device also can be used as a signal generator for electric speed controller (ESC), then you can test your motor system without using a transmitter and receiver.
* There are 3 modes to check servos or ESC:
◎Manual mode: turn the knob with different speed, check the reaction time.
◎Neutral mode: make the servo go back to the neutral point.
◎Automatic "window wiper" mode: make the servo swing like a window wipers in the biggest angle.
*It can connect 1-3 servos simultaneously and test such as 1-3 servos consistency and so on.
* You can also connect 1-3 ESC to test and compare their reaction time respectively.
* It can connect 3 servos of the CCPM helicopters and select servos.
* It can also connect the servo of airplanes install the steering-box and adjust planes by using such as the neutral mode and so on.

No more looking for a battery to run your 12v chargers

20A Output Switching DC Power Supply
Input: 100-240V AC
Output: +12V DC 20A (two way outputs)
Weight: 1500g /53.3 oz
Size: 23 x 20.5 x 8 cm

G.T.Power Rc Multi Distributor
Input: ≤20V DC
Output: 4 units outputs, current ≤ 15A
CH1 output current: ≤30A
Weight: 230g
Size: 160 x 60 x 35 mm
Output plug type: 3.5mm banana connector

This is the THUNDER T6 Multi charger.
The THUNDER T6 Multi charger allows you to plug 4 batteries into on charger simultaneously, and it will intelligently and automatically charge all 4 of them at once to their maximum capacity. To top of it, the batteries being charged do not even need to have the same configuration. You can connect different chemistry nimh,NiCd,LiPo,LiFe batteries into any of the charging ports.

Includes:
1 x charger
1 x Balance harness for Align/HiModel batteries
1 x Alligator Clips Cable
1 x conversion cable set (5pcs)
1 x USB cable
1 x English manual
1 x disk

Includes:
1 x charger
1 x Balance harness for Align/HiModel batteries
1 x Alligator Clips Cable
1 x conversion cable set (5pcs)
1 x USB cable
1 x English manual
1 x disk

This battery indicator is a great and easy way to keep check on your planes battery charge. It also can help remind you to turn off your plane after a flight if it is fitted on board.